Poly Classic D Melt Blown Cartridge Filter
Poly Classic D melt blown cartridge filter is pure polypropylene of special structure with great dirty holding capacity depth filter, which is an exceptional value for general applications where long life, high flow rate purity and low change-out frequency are required. It true-graded density filter material (lower density at the surface, with progressively higher density toward the center of the filter) captures particles throughout the entire filter depth. This excellent performance ensure the filter longer life and fewer change-outs than existing general melt-blown filters.
Features
● Graded pore structure enhances dirt holding capacity
● High contaminant removal efficiency
● Wide application
● Great flow rate and low pressure drop
● Long service life
Application
● Pre-RO
● Electronic
● Oil injection water
● Chemical solvents
● Drinking water treatment
● Cooling water
Specification
Materials of Construction |
|
Filter Media |
Polypropylene |
End Cap Material |
NA or Polypropylene |
Core |
Polypropylene |
End Cap |
222 Flat/222 Fin/226 Flat/226 Fin/DOE |
O-Rings |
Silicone/EPDM/Viton/NBR |
Dimensions(Nominal) |
|
Nominal Outside Diameter : |
2.5inch/63±1(mm) |
Nominal Inside Diameter |
1.1inch/28mm) |
Length |
10inch,20inch,30inch,40inch, |
Micron Ratings |
1μm,3μm,5μm,10μm,20μm, |
Operating Condition |
|
Maximum Temperature: |
180℉ (82 ℃) |
Maximum Pressure: |
50psi (3.5bar) @ 68 ℉ (20 ℃) |
Recommended change-out pressure: |
35psi (2.4bar) @ 68 ℉ (20 ℃) |
Order Information
Category:
Depth Filter
Keywords:
Roll Membrane | High Flow Filter | PP Pleated Filter
Contact Us
Tel: +86-513-89157856
Email: sales@delta-filtration.com
Product Description
Poly Classic D melt blown cartridge filter is pure polypropylene of special structure with great dirty holding capacity depth filter, which is an exceptional value for general applications where long life, high flow rate purity and low change-out frequency are required. It true-graded density filter material (lower density at the surface, with progressively higher density toward the center of the filter) captures particles throughout the entire filter depth. This excellent performance ensure the filter longer life and fewer change-outs than existing general melt-blown filters.
Features
● Graded pore structure enhances dirt holding capacity
● High contaminant removal efficiency
● Wide application
● Great flow rate and low pressure drop
● Long service life
Application
● Pre-RO
● Electronic
● Oil injection water
● Chemical solvents
● Drinking water treatment
● Cooling water
Specification
Materials of Construction |
|
Filter Media |
Polypropylene |
End Cap Material |
NA or Polypropylene |
Core |
Polypropylene |
End Cap |
222 Flat/222 Fin/226 Flat/226 Fin/DOE |
O-Rings |
Silicone/EPDM/Viton/NBR |
Dimensions(Nominal) |
|
Nominal Outside Diameter : |
2.5inch/63±1(mm) |
Nominal Inside Diameter |
1.1inch/28mm) |
Length |
10inch,20inch,30inch,40inch, |
Micron Ratings |
1μm,3μm,5μm,10μm,20μm, |
Operating Condition |
|
Maximum Temperature: |
180℉ (82 ℃) |
Maximum Pressure: |
50psi (3.5bar) @ 68 ℉ (20 ℃) |
Recommended change-out pressure: |
35psi (2.4bar) @ 68 ℉ (20 ℃) |
Order Information
Related Products
Send Inquiry